oktowncar
Well-known member
If you have any 3D printer files to replicate a hard to find part/piece for the Lincoln Town car and would like to share them please post them here.
-
-
This section is for questions that have already been answered. It's a place for people to find answers to questions - not ask questions. It is called "Frequently Asked Questions". Your question has not been established as frequently asked - so it does not belong here.
There is a support section for EVERY Lincoln model. If you have a question that needs an answer, please CLICK HERE to go to the homepage and select the section for your specific model. Thank you!
3D Printer files for parts & Misc.
- Thread starter oktowncar
- Start date
oktowncar
Well-known member
Lincoln Town Car Door Armrest Latch Repair Tabs/Clip
from member: LassetexanLincoln Town Car Door Armrest Latch Repair Tabs/Clip by Lassetexan
This is how I repaired the Lincoln Town Car Door Armrest Latch.The latch broke and this is how to repair it without buying a complete new part.You don't have to take the door-side apart, use a sharp knife to take some material off the button to make room for the tabs/clip, push the button back...
www.thingiverse.com
oktowncar
Well-known member
4 button FOB Case
www.thingiverse.com
Ford Four Button Remote Case by BryanDedeur
Ford Four Button Keyless Entry Remote Case. This part is Compatible with the following vehicles and part numbers:2001-2012 Ford Escape2007-2009 Ford Crown Victoria1998-2003 Ford Escort1998-2012 Ford Expedition1998-2013 Ford Explorer2001-2010 Ford Explorer Sport Trac2005-2007 Ford Five...
www.thingiverse.com
oktowncar
Well-known member
Trunk lettering
www.thingiverse.com
Lincoln Town Car out side text by M7md_says_hello
Lincoln Town Car out side text for those who has a lincoln town car and 3d printer, You can print the text and adhesive it to the back of the car.print it using 2 different filament for beautiful results.
www.thingiverse.com
______________________________
oktowncar
Well-known member
Fuel neck spacer for Panther Platform
www.thingiverse.com
Fuel Neck Spacer for Panther Platform Cras by LordAeneasTell
This is a printable fuel neck spacer on Mercury Grand Marquis, Crown Victoria, Lincoln Town Car. If an aftermarket fuel neck is purchased with the end cap too large for the old spacer, this will work.
www.thingiverse.com
oktowncar
Well-known member
(98-02) Double DIN frame/panel for Kenwood/JVC
www.thingiverse.com
Lincoln Town Car 98-02 double din panel / frame (JVC, KENWOOD) by fx600
Simple double din dash for Lincoln Town Car 98-02. I created it for JVC KW-M560BT (short body), similar KENWOOD models will also fit. After print U have to drill holes for bolts.
www.thingiverse.com
oktowncar
Well-known member
FL-820S Filter Wrench ( 3/8 Drive or Hand )
oktowncar
Well-known member
Lincoln Town Car 98-02 headlamp cover bolt/clip/knob
Lincoln Town Car 98-02 headlamp cover bolt/clip/knob by fx600
Plastic knob (clip) used in Town Car, CV etc, to hold plastic sight shield cover which is located over headlamps.
www.thingiverse.com
______________________________
Great products:
- VIN Check
- Windshield repair kit
- Clean your leather!
- Safe Emergency Charging
- Chemical Guys HydroSpeed Ceramic Quick Detailer
- Chemical Guys HydroCharge High-Gloss Hydrophobic SI02 Ceramic Spray Coating
- Get a dash cam!
- Auto Buyers Market
- Foreign invaders vs USA gangs
- VIN Check
- Windshield repair kit
- Clean your leather!
- Safe Emergency Charging
- Chemical Guys HydroSpeed Ceramic Quick Detailer
- Chemical Guys HydroCharge High-Gloss Hydrophobic SI02 Ceramic Spray Coating
- Get a dash cam!
- Auto Buyers Market
- Foreign invaders vs USA gangs
 | ||||
 |  |  |  |  |
 |  | |||
